contact gap
英 [ˈkɒntækt ɡæp]
美 [ˈkɑːntækt ɡæp]
触点间隙
双语例句
- Contact gap: Over3mm to meet European safety standard.
触点间隙大于3mm，满足欧盟安全标准。 - At the cellular level, this can be envisioned as follows: At a synapse, the two communicating nerve cells do not come in direct contact but are separated by a small gap.
在细胞水平上，这种现象可以这样描述：在突触连接处，两个可沟通的神经元并不直接连接而是中间有个小小的缝隙。 - Parameters of contact layer are determined when deformation of contact layer is equal to initial gap which is proposed in the criterion of penstock.
另外，接触层参数可通过其变形与规范建议的初始缝隙相匹配的原则加以确定。 - Contact effect is analyzed by using gap element in the delamination region without friction being considered.
通过在分层区域内引入虚杆单元来防止上、下子板发生相互重叠，并假设接触区内没有摩擦。 - Considering the gap between steel lining and concrete lining as the imperfect contact, contact layer is proposed to simulate the gap in the combined work analysis.
针对这种不密实接触问题，采用厚壁圆环组合环法，提出了在钢衬和混凝土之间设置接触层的钢衬、混凝土衬圈和围岩三者联合受力分析方法。 - A finite element modeling and analysis of the assembly of a breech mechanism in locking condition was carried out with special finite element techniques such as contact element, gap element and spring element.
利用接触元、间隙元和弹簧元等特殊单元，对某大口径火炮的炮尾-闩体-曲臂机构进行了闭锁状态下装配体有限元建模和分析。 - In this paper, the relationship between the value of axial magnetic field produced by coil structure contact and the sizes of contact gap often used in vacuum interrupter were calculated and analysed.
通过计算分析讨论了真空灭弧室线圈式触头产生的纵向磁场的大小与线圈结构尺寸的关系； - VT breakdown reasons and treatment methods of neutral point contact gap of GIS
GIS中电压互感器中性点接地间隙击穿原因及处理方法 - The author used the contact theory to found the gap element, and used it to solve the contact force.
利用现有的接触理论和计算方法，在模型的接触处构造了间隙单元来求解接触压力。 - The paper expounds the quantitative models of dielectric recovery process and voltage recovery process in contact gap, compares the theory criterions about various contacts breaking capacities, and discusses the importance of increasing breaking capacity by optimum seeking and improving contact material.
阐述了触头间隙介质恢复过程和电压恢复过程的定量模型，分析比较了已有的触头分断能力理论判据，论述了触头材料的优选与改进对提高分断能力的重要性。 - Experimental results indicate that Si-Ga replacement diffusion is the essence to obtain a good ohmic contact to n-typs GaP under the optimum alloying condition.
实验结果表明，在最佳微合金条件下，Si-Ga替位扩散是获得良好欧姆接触的实质。 - The Study and Improvement for the Contact Fault Between the Air Gap of the Stator and Rotor of the Bulb Tubular Hydrogenerators
对灯泡贯流式发电机定转子扫膛事故的研究和改进意见 - Based on contact and gap heat transfer theroy, a mathematical model on the mold dynamic heat flux of continuous casting of steel is developed.
本文从接触一间隙传热原理出发建立起结晶器动态热流数学模型，它与铸坯凝固传热计算相结合，预报了连续铸坯钢的过程。 - The parting face between casting and mould is divided as contact region and air gap region.
在解决摇枕、侧架等零件凝固收缩后铸件/铸型气隙热阻问题，再次创造性提出将铸件与铸型之间界面分解为紧密接触区和气隙区的热阻模型。 - Furthermore, the contact pressure, real area of contact, and average gap of real rough surfaces under the elastic, elastic-perfectly-plastic, and the elasto-plastic contact conditions are numerically investigated and the results are compared.
最后，用数值结果分析对比了真实粗糙表面在弹性、弹性-理想塑性和弹塑性接触状态下的接触压力、真实接触面积和平均间隙。 - Considering Contact Element of Gap
考虑缝隙的接触单元 - The experiment results show that the gravity has an effect on the wetting behavior of GaSb molten drop. The contact angle of GaSb drop with GaP and BN substrates in space is larger than that on the earth.
实验表明，重力因素对润湿性存在影响，空间微重力条件下测得的GaSb熔滴与GaP及BN基片的接触角比地面测量的大。 - Soluting Three-dimensional Elastic Contact Problem by GAP Element Method
用间隙单元法求解三维弹性接触问题 - To solve the nonlinear contact problems, a reasonable solution via linear gap element provided by MSC Nastran is given. This method is applied to engineering design. By analyzing the finite element model, the important basis for structure optimization and strength analysis is provided.
针对非线性的接触问题，使用MSCNASTRAN的线性间隙单元给出合理的求解方案，并应用于工程设计的实践中，通过对有限元模型分析的结果，为结构优化和强度分析提供重要依据。 - The solution model of three dimensional elastic contact problem is established by using GAP element method in this paper. GAP element in the I DEAS software makes the second development to solve the contact problem.
采用GAP单元法建立了三维弹性接触问题的求解模型，并对IDEAS软件中缝单元进行二次开发用以求解接触问题。 - Effects of 7 contact design parameters on magnetic field characteristics of vacuum interrupters with cup type axial magnetic field contacts are studied by using 3D finite element method. The results show that: { 1} Axial magnetic flux density weakens with increasing contact diameter or contact gap.
用三维有限元法研究了7个设计参数对杯状纵磁触头的纵向磁感应强度、纵向磁场滞后时间、杯中和触头片中电流密度最大值以及导体电阻值的影响。 - As the elastic deformation of plate unit, it can be calculated by Hertz contact formula and is regarded as a gap to be substituted to the total matrix equality, so the three dimensional distribution of load peculiarities of mill roller bearing can be achieved.
对于板单元的弹性变形，用Hertz接触公式，将其变形以等效间隙代入总体矩阵方程中，从而获得轧机滚动轴承负荷特性的三维分布。 - Comparative study on direct contact and air gap membrane distillation
直接接触式与气隙式膜蒸馏的比较研究 - The positioning of tapered interface of KM toolholder under different clamping forces is simulated and analyzed by using Finite-element Method. Data about radial displacement, contact stress and taper interface gap are obtained.
针对在不同夹紧力下KM刀柄的锥面定位进行了有限元模拟及分析，获得了其径向位移、接触应力和锥面间隙变化的具体数据。 - To fully consider the influence of arcing energy, product structure, contact material and sample dispersion on degradation of contact gap, the physical-of-failure degradation model of space relays is established according to cumulative damage theory.
采用累积损伤理论建立了航天继电器失效物理退化模型。该模型充分考虑了燃弧能量、产品结构、触点材料属性以及样品分散性对触点间隙退化的影响。 - Then in smaller detecting area, with the coarse-to-fine edge detection algorithm, the system can find the edges of two contact points and calculate the gap between two relay contact points.
然后在更小的锁定检测区域，采用由粗到精边缘检测算法，检测两接触点边缘，计算出继电器两触点的间距。 - The increase of contact gap causes the saturation characteristics of insulation strength between the contacts, which limits the development of single vacuum circuit breaker to higher voltage grade.
真空开关触头间绝缘强度随间隙距离增大的饱和特性，使得单断口真空断路器的向高电压等级发展受到限制，利用多个真空断路器构成的多断口真空断路器可以弥补这一缺点。 - Imaging examination: implants contact with bone closely, there is no gap between them.
影像学结果：A组种植体与骨组织接触紧密，未见间隙存在。 - Contact plate gap measurement cannot timely indicate the change of plate gap caused by plate wear.
接触式测量法不能实时反映磨片磨损对磨盘间隙的影响。